T TimoraMagic watch

Support

Usually within 1–2 business days · kpenlab@163.com

Timora controls PITATA Bluetooth watches, X speaker microphones and KPEN e-paper pendants.

The watch won't connect

  1. Make sure the watch is charged and awake.
  2. Open the Devices tab and switch the watch on. The status line should read “Connecting…”.
  3. If it stays there longer than 20 seconds, switch it off and on again — the app cancels a stuck connection after about 8 seconds and rescans.
  4. Make sure the watch is not still connected to the official PITATA app on another phone.
  5. Last resort: turn the phone's Bluetooth off and on, then retry.

I speak, but the hands don't move

  1. On the Devices tab the watch must read “Connected”, not just be switched on.
  2. The microphone must read “Connected” as well.
  3. Speech recognition needs the offline model for your language; iOS downloads it the first time dictation is used.
  4. If “Confirm before sending” is on in the Perform tab, the time is only sent when you press the mic button again or tap the screen.

Can I try it without the hardware?

You can open the app and browse every screen, and the Calibrate tab explains each command. Driving the hands, the microphone button and the e-paper refresh all need the real devices.

The e-paper pendant doesn't refresh

  1. It only refreshes during the crown routine: a spectator pulls the crown, dials a time and pushes it back. It is not a clock face.
  2. Make sure it is switched on in the Devices tab. If two units are nearby, use “Choose e-paper” to pick the right one.
  3. One refresh takes about two seconds. If it fails, the status line reports a timeout after 8 seconds.

Which devices are supported?

iPhone with iOS 16 or later. iPad is not supported. The app talks to the hardware over Bluetooth Low Energy.

Will my settings be lost?

Settings and the last connected device are stored on the phone and are removed if you delete the app. There is no cloud backup in this version.

Still stuck?

Email kpenlab@163.com and tell us which device, what the status line says, and roughly when it happened.

使用支持

通常 1~2 个工作日内回复 · kpenlab@163.com

Timora 用于控制 PITATA 蓝牙手表、X speaker 蓝牙麦克风与 KPEN 墨水屏挂件。

手表连不上

  1. 确认手表有电、已唤醒。
  2. 打开「设备」页,把手表开关打开,状态应显示「正在连接…」。
  3. 超过 20 秒还停在那里,关掉再打开一次 —— App 会在约 8 秒后取消卡住的连接并重新扫描。
  4. 确认手表没有还连着另一台手机上的官方 PITATA App。
  5. 最后手段:把手机关蓝牙再打开,然后重试。

我说了话,指针不动

  1. 看「设备」页:手表要显示「已连接」,而不只是开关打开。
  2. 麦克风也要显示「已连接」。
  3. 语音识别依赖系统的离线模型,第一次使用时 iOS 会自行下载。
  4. 如果「表演」页的「识别后需确认」开着,识别出的时间要再按一次麦克风按键或点屏幕才会发出。

没有硬件能体验吗

可以打开 App 浏览全部界面,「校准」页里也有每条指令的说明。但驱动指针、麦克风按键、墨水屏挂件刷新都需要真机。

墨水屏挂件不刷新

  1. 墨水屏挂件只在表冠玩法时刷新:观众拉开表冠、拨出时间、按回,才会把这个时间推到屏上。它不是时钟。
  2. 确认「设备」页里它是打开的。附近有两台时,用「选择墨水屏挂件」挑正确的那台。
  3. 一次上屏约需两秒;失败时状态会在 8 秒后提示超时。

支持哪些设备

iPhone,iOS 16 及以上。不支持 iPad。App 通过低功耗蓝牙与硬件通信。

设置会丢吗

设置和上次连接的设备保存在手机上,删除 App 即清除。当前版本没有云端备份。

还是不行?

发邮件到 kpenlab@163.com,说明哪台设备、状态栏显示什么、大概什么时候发生的。